JavaScript is disabled in your browser.
Clicking the Submit Answers for Grading button below will result in an error and your answers will be cleared. Please enable JavaScript before submitting your quiz for grading. Consult your browser's Help feature for information on enabling JavaScript.
Lab Quiz
Skeletal Muscle Physiology
Lab Quiz
This activity contains 25 questions.
Refer to Activity 2: Determining the Latent Period. The latent period between time of innervation and time of contraction is:
0.55 msec.
1.36 msec.
1.84 msec.
2.78 msec.
3.12 msec.
Refer to Activity 2. During the latent period, what is actually happening?
The electrochemical impulse is being transmitted.
The muscle is recruiting myosin to the site of contraction.
The sarcoplasmic reticulum is releasing calcium into the sarcoplasm.
The actin and myosin filaments are sliding.
Nothing is occurring.
Refer to Activity 3: Investigating Graded Muscle Response to Increased Stimulus Intensity. What is the minimal or threshold stimulus?
0.2 volts
0.4 volts
0.6 volts
0.8 volts
1.0 volt
Refer to Activity 3. The maximal stimulus is approximately:
10 volts
8 volts
6 volts
4 volts
2 volts
Refer to Activity 3. The increase in force is a result of:
(a) more voltage being delivered to the whole muscle.
(b) more muscle fibers being activated.
(c) more calcium being absorbed.
both (a) and (b)
all of the above
Refer to Question #5. This increase represents which type of summation?
Multiple motor unit summation
Incomplete tetanus
Complete tetanus
Twitch
Wave summation
Refer to Activity 4: Investigating Treppe. With each subsequent stimulus, the force produced _____________ , provided the stimuli are delivered relatively close together.
decreases slightly
increases slightly
remains the same
decreases greatly
increases greatly
Refer to Activity 5: Investigating Wave Summation. The peak force produced in the second contraction is ___________ that produced by the first stimulus.
greater than
less than
equal to
produced by a different contraction mechanism than
Refer to Activity 5. When the Single Stimulus button is clicked several times in rapid succession, the total force production:
Is even greater.
decreases.
remains the same.
increases to a certain point, then plateaus.
decreases, then begins to increase after several seconds.
Refer to Activity 5. At Active Force = 2 gms, when the Single Stimulus button is clicked rapidly several times,
a smooth sustained contraction is produced.
the twitch tracing rises and falls.
the twitch tracing continues to rise.
the force generated does not change.
the twitch tracing plateaus.
Refer to Activity 5. At Active Force = 3 gms,
the trace produces a single twitch.
the trace is more erratic.
the trace shows a flat line.
the trace is smoother.
the trace does not change from Active Force = 2 gms.
Refer to Question #11. To this point, the maximal stimulus has been used. If a lower voltage were used,
the force produced would be the same.
there would not be enough stimulus to produce a contraction.
the force produced would be greater.
more muscle fibers would be recruited for contraction.
the force produced would be lower.
Human skeletal muscles work to achieve a smooth, steady contraction at all desired levels of force through
(a) stimulus frequency.
(b) calcium concentrations.
(c) recruitment of motor units.
both (a) and (b)
both (a) and (c)
Refer to Activity 6: Investigating Fusion Frequency. The appearance for the multiple stimulus tracings shows that at ________ the force rises and falls.
10 stimuli/sec
20 stimuli/sec
30 stimuli/sec
40 stimuli/sec
50 stimuli/sec
Refer to Activity 6. When the stimulation rate is changed by 10 stimuli/sec up to 150 stimuli/sec, how do the tracings change?
The active force produced by the muscles stays the same.
The active force produced by the muscles decreases.
The tracings become smoother.
The tracings become more erratic.
The force and tracings do not change.
Refer to Activity 6. The fusion frequency or the tetanus is achieved at ________ stimuli/sec.
100
120
140
160
180
Refer to Activity 6. At Force = 2 gms, what is the stimulus intensity that produces smooth, sustained force?
100 stimuli/sec and 1.0 volt.
120 stimuli/sec and 1.2 volts.
140 stimuli/sec and 1.4 volts.
160 stimuli/sec and 1.6 volts.
180 stimuli/sec and 1.8 volts.
Refer to Activity 6. At Force = 3 gms, what is the stimulus intensity that produced smooth, sustained force?
100 stimuli/sec and 1.8 volts.
120 stimuli/sec and 1.6 volts.
140 stimuli/sec and 1.4 volts.
160 stimuli/sec and 1.2 volts.
180 stimuli/sec and 1.0 volts.
Refer to Activity 6. To achieve smooth contractions at different force levels, what is needed?
(a) An increase in the stimulation rate.
(b) A decrease in voltage.
(c) An increase in voltage.
Both (a) and (b)
Both (a) and (c)
Refer to Activity 7: Investigating Muscle Fatigue. Why does the force decrease with time?
The muscle is in aerobic respiration.
ATP is used up faster than it is produced.
The voltage is decreased.
The stimulus stops.
The Krebs cycle shuts down.
Refer to Activity 8: Investigating Isometric Contraction. What happens to the passive forces as the muscle length is increased from 50 mm to 100 mm?
The passive force remains at zero.
The passive force increases sharply.
The passive force decreases sharply.
The passive force turns into active force.
The passive force recruits more motor units.
Refer to Activity 8. What happens to the active force as the muscle length is increased from 50 mm to 100 mm?
The active force increases steadily until 55 mm and then falls with increasing length.
The active force increases steadily until 65 mm and then falls with increasing length.
The active force increases steadily until 75 mm and then falls with increasing length.
The active force increases steadily until 85 mm and then falls with increasing length.
The active force increases steadily until 95 mm and then falls with increasing length.
Refer to Activity 9: Investigating the Effect of Load on Skeletal Muscle. From the plot results, which of the following is true about the resistance and initial velocity?
As the resistance decreases, the initial velocity of shortening decreases.
As the resistance decreases, the initial velocity of shortening increases.
As the resistance increases, the initial velocity of shortening decreases.
As the resistance increases, the initial velocity of shortening increases.
There is no change.
Can a completely isometric contraction be set up?
Yes
No
Can a completely isotonic contraction be set up?
Yes
No
The Clear Answers feature requires scripting to function. Your browser either does not support scripting or you have turned scripting off. So, the Clear Answers feature will not work. Note that you do not need to use the Clear Answers feature in order to use this site. You can change your answers for each question individually.
Your browser either does not support scripting or you have turned scripting off. Because of this, the answer choices will NOT appear in a different order each time the page is loaded, though that is mentioned below. Note that you do not need this feature to use this site.
Answer choices in this exercise appear in a different order each time the page
is loaded.
Copyright © 1995-2008, Pearson Education, Inc., publishing as Pearson Benjamin Cummings
Legal and Privacy Terms